Configuring a Verify DP Heading input on PORT3 Configuring a Verify DP Heading input through USB For LD2 What is the expected latency from one PPS to the ZDA telegram? Guia rápido do LD2 da VERIPOS (LD2 Quick Guide - Brazilian Portuguese) How can I change the IP address of my LD2(S) when using Verify-DP? How can I determine what L-band firmware versions are installed on the LD2/LD2S? How do I check the GLONASS option on my Topcon GNSS Receiver in an LD2 IMU? How do I check the L-band reception status of my LD2/LD2S demodulator? How do I check version number of my LD2? How do I configure a Position Output on port P1 of my LD2/LD2S? How do I configure my LD2 (Topcon GPS card) to output a ZDA and 1PPS string from Port 1 of the LD2? How do I configure my LD2 to use the Apex service? How do I manually select MF Stations on my LD2 IMU? How do I Remove Standard+ Service in my LD2/LD2S? How do I select MF or HF Auto Frequency on my LD2? How do I upgrade the GLONASS option on my Topcon GNSS Receiver? I have just changed beams and my station list is not fully populated why is this? LD2 DP Bridge Card LD2 Installation Manual LD2 Operations Manual LD2 Quick Guide LD2 Setup - Configuring PPS & ZDA Output from Topcon GPS Card Selecting An LD2 L-band Beam What are the tracking capabilities of my LD2 and what services are available to my unit? What data is available on the LD2 Ethernet port? What do the status LED's on the front panel of the LD2 show? What is demodulator Channel 16 used for and how I configure it? What NMEA telegrams are available for output from the LD2/LD2S?

How do I manually select MF Stations on my LD2 IMU?

Note: These menus will only appear if the optional beacon SBX-4 or the Thales 3011HF/MF receiver card is installed. The method of entering Manual Mode is the same on both receiver types; however the display will show HF/MF Receiver for a 3011 card and Beacon Receiver for an SBX-4 card.

SBx-4 Beacon Receiver

press *Enter* then *Page*

From the above screen, press *Enter* then *Page* until you display the screen below:

until you display the screen

Press *Enter* to display:

 Press *Enter* to display

Press *Enter* again to display the configuration menu:

Press *Enter* again to display the configuration menu

Press *Enter* to move the cursor to the mode and press *Toggle* to display Manual:

Press *Enter* to move the cursor to the mode and press *Toggle* to display Manual

Press *Enter* to move the cursor to the frequency

Press *Toggle* to change the frequency and *Enter* to accept the digit and move onto the next.

After the final frequency digit has been entered the cursor will move onto the Data rate. Press toggle to set this to the desired data rate and pressing enter will then accept the new settings and program the receiver to this station.

To check the signal being received press *Page* until the following screen is displayed:

To check the signal being received press *Page* until the following screen is displayed

Press *Enter* to display the Signal Status

Press *Enter* to display the Signal Status

Thales 3011 HF/MF Receiver

Thales 3011 HF/MF Receiver

From the above screen, press *Enter* to display:

From the above screen, press *Enter* to display

From the above screen, press *Page* to display:

 From the above screen, press *Page* to display

Press *Enter* again to display the configuration menu:

Press *Enter* again to display the configuration menu

Press *Enter* to move the cursor to the mode and press *Toggle* to display Manual:

Press *Enter* to move the cursor to the mode and press *Toggle* to display Manual

Press *Enter* to move the cursor to the frequency

Press *Toggle* to change the frequency and *Enter* to accept the digit and move onto the next.

After the final frequency digit has been entered the cursor will move onto the Data rate. Press *Toggle* to set this to the desired data rate and pressing *Enter* will then accept the new settings and program the receiver to this station.

To program CH2 for manual frequency:

Press *Toggle* when the cursor is on CH1 to enter the CH2 configuration page Repeat the steps for CH1 to program CH2.

To check the signal being received press *Page* until the following screen is displayed:

To check the signal being received press *Page* until the following screen is displayed

Press *Enter* to display the Signal Status:

Press *Enter* to display the Signal Status