How can I interface RTCM data from two LD6 units to Verify QC using a single LAN connection (Dual beam corrections)? How do I archive data on an LD6? How do I change a beam on an LD6? How do I change the PPP solution when my LD6 is enabled for both Apex and Ultra services? How do I check the GNSS tracking capabilities of my LD6 version 8 or 50? How do I check the IP address of my LD6? How do I check which version of LD6 I have? How do I configure an LD6 to receive RTK corrections? How do I configure LD6 TRINAV Output? How do I configure my LD6 to use the Apex service? How do I configure NMEA Sentences on an LD6 versions 8 or 50? How do I configure NMEA sentences on LD6 versions 101 and 105? How do I correctly shut down a LD6? How do I enable and output a heading from an LD6? How do I enable SBAS on my LD6 IMU? How do I factory reset my LD6 unit? How do I implement a basic LAN interface between an LD6 and my Verify QC computer? (v1.11 or later) How do I interface my antennas to the LD6? How do I manually enter an L-band frequency on the LD6? How do I remove satellites from my LD6 version 8 or 50? How do I set up LD6 Outputs for VQC? How do you load a Verify QC config onto the LD6 while in QC mode? I have just changed beams and my station list is not fully populated- Why is this? What are the serial pin-outs of the LD6? What are the tracking capabilities of my LD6 and what services are available to my unit? What data is available on the LD6 Ethernet ports? What direction is the heading on my LD6? What files should I send for data analysis from a LD6 while running quantum on board? What is the best way to interface Verify QC to my LD6 units? What is the expected latency from one PPS to the NMEA ZDA telegram on the LD6? What is the PPS voltage and pulse width of my LD6? What version of GNSS card is installed in my LD6?

How do I enable and output a heading from an LD6?

LD6 105 systems (running software version 105.0.0.10 or later) are capable of calculating a GNSS heading solution. In order to use this feature, the LD6 may need to be enabled with a heading license PIN. A license PIN can be obtained from your Veripos project manager, there may be a cost with enabling this feature.

Once the heading licence PIN is obtained, navigate from the main screen to Settings > License > Config then choose Heading. A new page will appear asking you to Enter License PIN. Enter the license PIN using the Up/ Down arrows and Insert button, to apply press Confirm. 

Enter the license PIN using the Up/ Down arrows and Insert button, to apply press Confirm.

A message will then appear to indicate if the code entered was valid. If the code was not valid, check and re-enter. If it is still not accepted, contact the Veripos Helpdesk for assistance.

If the code was not valid, check and re-enter. If it is still not accepted, contact the VERIPOS Helpdesk for assistance.

Once the Heading functionality is successfully enabled, the heading will become available in the Position info page that can be accessed by navigating from the LD6 home screen to GNSS > Status > Position Info

Once the Heading functionality is successfully enabled, the heading will become available in the Position info page

For the GNSS heading to be calculated by the LD6 a secondary GNSS antenna will need to be installed and connected to the LD6 auxiliary GNSS antenna connector.

To output the heading from the LD6, the NMEA HDT sentence has to be enabled on an existing or a new NMEA output . To enable HDT sentence, navigate from the LD6 home screen to GNSS > Config  then select either NMEAa, NMEAb or NMEAc output stream and then click Edit. Use the Up/Down arrows to enable HDT sentence and click Enable. The NMEA HDT sentence should now be available on the specified NMEA stream, for serial output an additional port may require to be configured. 



Related articles